TROY T22 TRX 10-22 CHASSIS
TROY T22 TRX 10-22 CHASSIS
Troy T22 TRX 10-22 Chassis – Ultra lightweight and modular, TROY T22 Chassis are the ultimate low-cost training solution for military and law enforcement. Built-on the Ruger 10-22, the T22 mimics all the features of the standard M4but utilizes lower cost 22LR ammunition.
The Sport T22 Chassis features a built-in legendary TROY spring-loaded M4 BattleSight™, pistol grip, adjustable stock and a free-floating barrel. TROY T22 Chassis Systems are compatible with all standard and bull barrels up to .926″ diameter. Patent Pending. Available in Black only.
TROY T22 TRX 10-22 CHASSIS FEATURES:
- Built in troy spring loaded battlesights
- Ultra light design
- Pistol grip
- Adjustable stock
- Free floating barrel
- Compatible with standard and bull barrels
- Compatible with standard TRX attachments
- Full length top picatinny rail
- Aluminum handguard and receiver housing
- Accepts standard AR-15 commercial stocks
- Front sight is adjustable for elevation
- Rear sight is adjustable for windage
TROY T22 TRX 10-22 CHASSIS BENEFITS:
- Modular design allows for unlimited mounting options
- Simple installation of 10/22® into chassis
- Full length rail allows for a wide variety of optics choices, not normally possible on a 10/22®
- Free floated barrel assists in improving accuracy
- Aluminum construction provides a tough and durable chassis for your 10/22®
HIGH TOWER ARMORY 10 22 PS90 STOCK
HIGH TOWER ARMORY 90/22 10 22 PS90 STOCK
HIGH TOWER ARMORY 90/22 10 22 PS90 STOCK – From tactical training to plinking, varmint hunting to home defense, the HTA 90/22™ from High Tower Armory™ is the perfect stock system for your shooting needs. The High Tower Armory 90/22 is a compact, maneuverable stock kit for the Ruger® 10/22® which utilizes a fully ambidextrous bullpup design for superior balance and ergonomics. This incredibly durable, military grade polymer stock will reduce the overall length of most 10/22’s to about 26 1/2 inches, just over the federally required minimum length for rifles. The HTA 90/22 also features a CNC machined monolithic aluminum Picatinny optics rail and aluminum bedding block, as well as an ambidextrous steel charging handle which cycles the factory 10/22 bolt from forward positions. The HTA 90/22 trigger linkage is made of Melonite treated steel for the most consistent and efficient transfer of energy, having a resistance to flex three times greater than aluminum by weight. A safety extension is included to allow the original factory safety to be activated, in addition to a safety selector located near the trigger. Also included is both an extended magazine and automatic bolt release which replace the factory releases and allow for much faster manipulation of your rifle’s controls. Additionally, a shell deflector can be attached to the stock making it safe and comfortable to shoot left handed. This kit comes complete with a removable dummy suppressor, two side mounted Picatinny rails, and a detachable ammunition storage box for holding spare rounds in the field. Accepts factory 10 round magazines as well as most aftermarket high capacity magazines. Fits factory 18 1/2″ and .920″ bull barrels at least 18 inches in length (17 1/4 inches from receiver face to muzzle). Made in the USA. *Ruger 10/22 not included.
IMPORTANT: PLEASE CHECK THAT YOUR RUGER 10/22 BARREL IS AT LEAST 18” IN LENGTH. MOST 10/22 barrels are long enough to produce a legal length rifle in the 90/22 stock system. However, some 10/22 variants and aftermarket barrels are shorter than 18″. Federal law requires rifles to have a minimum overall length of 26”. The HTA 90/22 requires a minimum barrel length of 18″ to achieve the 26″ overall length. You can check your barrel length by removing the barrel from the 10/22 receiver and measuring it from muzzle to breech.
HIGH TOWER ARMORY 90/22 10 22 PS90 STOCK SPECIFICATIONS
- Compact bullpup design
- Aluminum Picatinny optics rail
- Aluminum bedding block
- Detachable ammunition storage box
- Shell deflector included for ambidextrous use
- Detachable dummy suppressor
- Military grade polymer body construction
- Melonited steel ambidextrous charging handle
- Melonited steel trigger linkage
- Melonited steel extended automatic bolt release
- Two staged extended magazine release
- Two side mounted Picatinny rails for accessories
- Fits standard and bull barrels at least 18″ in length
- Made in the USA
- Fiber reinforced, custom blended polymer construction
- Milspec hardcoat anodized 6061 machined aluminum optics rail
- Milspec hardcoat anodized 6061 machined aluminum bedding block
- Steel charging handle with black Melonite finish
- Steel trigger linkage with black Melonite finish
- Stock length: 21 1/2″ long without 10/22 installed (not including dummy suppressor)
- Overall length: approx. 26 1/2″ long with factory 10/22 barrel
- Weight: 3.5 lbs
HIGH TOWER ARMORY 90/22 10 22 PS90 STOCK FAQ
Question: How can I tell if my 10/22 barrel is long enough to have a legal length rifle (26 inches) when installed in the 90/22?
Answer: MOST 10/22 factory barrels are of legal length. These include 10/22 carbine barrels that are considered 18 1/2 inches long. The HTA 90/22 is a bullpup style stock, which will shorten most 10/22 rifles to within 1/2 of an inch of the legal minimum length by moving the receiver and barrel rearward relative to a traditional stock. It is still very important, however, to check your rifle for length before purchasing the HTA 90/22 to avoid potential legal issues
The Bureau of Alcohol, Tobacco, and Firearms (ATF) requires a minimum overall length of 26 inches and a minimum barrel length of 16 inches on all rifles. YOU MAY NOT COUNT DETACHABLE MUZZLE DEVICES TOWARDS BARREL AND/OR OVERALL RIFLE LENGTH. The ATF does not consider removable barrel attachments as part of a barrel and therefore you must measure from the muzzle crown, not the end of a flash suppressor, muzzle break, etc that can be unscrewed. However, welded or integrally machined, non removable barrel attachments DO count towards barrel and overall length. It is a felony to be in possession of a rifle that does not meet these requirements, without having gone through the proper channels first. High Tower Armory is not responsible for legal fees and other expenses resulting from failure to properly check the length of your rifle, both before purchase and after installation. It is also the end user’s responsibility to check their local laws and regulations regarding the legality of this stock.
There are two methods for verifying that your rifle will reach the minimum length in this stock. The first method is to measure from the muzzle of the rifle (not including a removable muzzle device) to the point the barrel enters the receiver. In other words, measure the amount of barrel that is exposed. This length must be at least 17 1/4 inches. See image “Method 1”
The second method requires you to measure your 10/22 from the butt end of the receiver to the muzzle (not including a removable muzzle device). This length must be at least 23 3/8″ inches for a legal length rifle. See Image “Method 2”
HIGH TOWER ARMORY 10 22 PS90 STOCK MEASURING
High Tower Armory, LLC also highly recommends checking the overall length of your rifle once a HTA 90/22 kit is installed, to further verify the legality of your rifle.
Question: Will the HTA 90/22 work with .920 bull barrels?
Answer: Yes, any barrels with a .920 diameter will fit in the 90/22, as long as they are of legal length.
Question: Will the HTA 90/22 accept aftermarket magazines?
Answer: Yes, most aftermarket high capacity magazines will fit in the HTA 90/22. However, some magazines, including “tear-drop” mags, drum-mags, and Butler CreekTM mags that have protruding knobs for linking two mags together, may not fit into the 90/22 mag-well. EagleTM, Shooter’s RidgeTM, Ruger factory rotary magazines, and Ruger BX-25TMmagazines are a few examples of magazines that will work in the HTA 90/22.
Slide Fire 10 22 Stock SSAR-22
Leave it to the Slide Fire team to take the incredibly fun to shoot and accurate Ruger 10/22 and make it even more fun with their Slide Fire 10 22 Stock SSAR-22 ! I don’t even need to explain how cool this is. I smell the birth of a new site project. If you aren’t sure why you need the slide fire click the link below and be enlightened.
Slide Fire 10-22 Stock SSAR-22
Outfit your Ruger®10/22® for the ultimate rapid fire experience with the SSAR-22 Kit. It includes an SSAR-15® OGR stock, 3lb pull trigger, and Tactical-22 chassis. The 3lb Trigger is optimized for rapid fire action and the 10/22® chassis system is designed to enhance the functionality and aesthetics of a standard RUGER 10/22® rifle. This is more than an addition, it’s a complete overhaul on your rifle.
The Slide Fire 10 22 Stock SSAR-22 utilizes the same groundbreaking design and technology as the SSAR-15 line of stocks, offering the same level of performance, reliability, and superior craftsmanship for the classic 10/22 rifle. The SSAR-22 allows the shooter to safely bump fire their 10/22 rifle from the shoulder, effectively and legally simulating fully automatic fire, and allowing for an unprecedented measure of control that is severely lacking when attempting to bump fire a rifle in the traditional, “from-the-hip” manner.
The SSAR-22 features a shelf that positions the shooter’s index finger in a fixed position in front of the rifle’s trigger. To fire, the rifle is moved forward with the support hand pushing on the forend, thereby bringing the trigger to the shooter’s finger and discharging a round. The rifle’s recoil causes it to move rearward, allowing the trigger mechanism to reset. When the right amount of constant forward pressure is applied, the rifle will continue to fire as the trigger is brought forward and depressed by the shooter’s stationary index finger, causing the gun to Bump Fire. Only 4-6 lbs. of force is required, allowing shooters of any stature to enjoy the fast paced fun of the Slide Fire 10/22. With a little practice, the shooter will be capable of delivering accurate single shots, bursts, or even full magazine dumps on demand using the SSAR-22.
The SSAR-22 employs a simple stock locking mechanism that allows shooters to select between their preferred firing methods easily and quickly. In the extended or “Open” position, the rifle’s receiver is allowed to freely slide rearward during the recoil impulse into the stock, thereby allowing the gun to be bump fired. The stock may also be locked into a collapsed, or “Closed,” position into which the buffer tube attached to the chassis is held in place within the buttstock and unable to move, thereby facilitating semi-auto function.
The SSAR-22 is designed to be compatible with the Ruger 10/22 and clones. SSAR-22 Kit includes the chassis system platform, match grade trigger assembly, SBS stock, handguard with flattop rail for optic or sight mounting, interface block, nut retainer, hex key, mounting hardware, instructions, BATFE Approval Letter, and a lifetime factory warranty. Also included is an A2 pistol grip and collapsible, M4 buttstock for converting the 10/22 to a standard M4 configuration if extended semi-auto operation is desired. Made in the USA.
- Model: SSAR-22
- Stock Material: Reinforced High Strength Polymer
- Compatibility: Ruger 10/22
NOTE: The Left Hand Model has a fixed finger shelf located on the right side of the stock. The trigger will be blocked by this shelf and inaccessible when fired with the right hand.
Slide Fire 10 22 Stock SSAR-22